STRUCTURAL CONCRETE BUILDING CODE/COMMENTARY 318-137CODE COMMENTARYmodified in the 2005 edition to make the skin reinforcementspacing consistent with that of the flexural reinforcement.The size of the skin reinforcement is not specified; researchhas indicated that the spacing rather than bar size is ofprimary importance.10.21 Bar sizes No. 3 to No. 5 (orwelded wire reinforcement with a minimum area of 0.1 in.2per foot of depth) are typically provided.Where the provisions for deep beams, walls, or precastpanels require more reinforcement, those provisions (alongwith their spacing requirements) will govern.R10.7 — Deep beamsThe span-to-depth ratios used to define deep beams in the1999 and earlier Codes were based on papers published in1946 and 1953. The definitions of deep beams given in10.7.1 and 11.8.1 of these earlier Codes were different fromeach other and different from the current Code definitionthat is based on D-region behavior (see Appendix A). Thedefinitions of deep beams in Sections 10.7.1 and 11.8.1 areconsistent with each other and different from the definitionintroduced in 2002, which is based on D-region behavior(see Appendix A). Since 2002, the definitions of deepbeams in Sections 10.7.1 and 11.8.1 are consistent witheach other.This Code does not contain detailed requirements fordesigning deep beams for flexure except that nonlinearity ofstrain distribution and lateral buckling is to be considered.Gợi ý cho việc thiết kế của các chùm tia sâu cho congđược đưa ra trong tài liệu tham khảo 10,22, 10.23, và 10,24.da tăng cường hay prestressing thép để cáckhuôn mặt bên. Nó được phép bao gồm tăng cường như vậyở sức mạnh tính toán nếu một căng thẳng khả năng tương thíchphân tích được thực hiện để xác định các căng thẳng trong các cá nhânquán bar hoặc dây.Hình. R10.6.7-da tăng cường cho dầm và joists với h > 36 trong.10.7 — sâu dầm10.7.1 — sâu dầm là thành viên được nạp vào mộtphải đối mặt và hỗ trợ đối diện mặt vì vậy màthanh chống nén có thể phát triển giữa các tảivà hỗ trợ, và có một trong hai:rõ ràng (a) kéo dài, ln, bằng để hoặc ít hơn bốn lầnđộ sâu tổng thể của thành viên; hoặc(b) khu vực với tập trung tải trong vòng hai lần cáctài khoản của các độ sâu từ bộ mặt của sự hỗ trợ.Sâu chùm tia sẽ thiết kế hoặc tham gia vàotài khoản phi tuyến phân phối của căng thẳng, hoặc bởi phụ lục A.(Xem thêm 11.7.1 và 12.10.6.) Sự oằn bên phảiđược xem xét.10.7.2 — Vn của sâu chùm tia sẽ theo quy địnhvới 11.7.10.7.3-diện tích tối thiểu flexural căng thẳng tăng cường,Như, min, sẽ phù hợp với 10.5.
đang được dịch, vui lòng đợi..