Kỹ thuật voltammetric bóc là một thú vị thay đổi người bản xứ để phát hiện dấu vết mức độ của kim loại nặng trongma trận mặn cao. Các kỹ thuật trình bày một quan trọngđộ nhạy cảm do khả năng duy nhất preconcentrate tar-get loài trong bước tích lũy ngày làm việcđiện cực, bên cạnh của nó kết hợp với xung đo lườngkỹ thuật tạo ra một tỷ lệ tín hiệu đến nền rất thuận lợi. Dựa trên Mercury điện cực, chẳng hạn như thủy ngânphim điện cực (MFE), và treo thủy ngân thả điện cực(HMDE), theo truyền thống đã được sử dụng trong tước kỹ thuậtdo lợi thế của họ, chẳng hạn như độ nhạy cảm cao, repro-ducibility, độ tinh khiết của hydro bề mặt, cao overpotential,và khả năng hình thành hỗn hợp. Do đó, họ cóđược công nhận là các điện cực nhạy cảm nhất cho deter mination của kim loại nặng [5]. Cụ thể hơn, HMDE cóthành công được sử dụng trong việc xác định Pb và đĩa Cd trongnước biển mẫu [6,7]. Gần đây, Süren et al. giới thiệumột sửa đổi trong hệ thống bởi ngay trước vi phânxung tước voltammetry (DPSV) của bộ sưu tậpcủa tổ hợp với 8-hydroxyquinoline (oxine) vào các điện cực mer cury [2]. Mặt khác, một số studieswith MFEđược báo cáo [8-13]. Ví dụ, Khoo và Quách điều traCác muối mercury(I)/(II) như gia cường cho carbon dán elec-trodes [8]. Inanattempt toworkwithenvironmentally thân thiệnkim loại, một nghiên cứu so sánh của phiên bản đồng thời determina-tion của kim loại nặng trong cao mặn mẫu bằng cách sử dụng ASVthủy ngân và bitmut phim điện cực như làm việc elec-trodes được thực hiện [9].Kiểu dáng khác nhau dựa trên than chì-epoxy composite elec-trodes (GECE) cho điện hóa phân tích bóc của kim loạiđã được sử dụng trong phòng thí nghiệm của chúng tôi. GECE mà không có bất kỳ modi-fication thứ nhất đã được áp dụng trong kim loại phân tích [14-16]. AGECE sự hiện diện của bitmut trong các giải pháp đo[17] cũng như một Bi (NO3) 3-GECE [18] mà đại diện cho một GECESửa đổi lần trong nội bộ với bitmut nitrat muối cũng đãnghiên cứu và áp dụng [19].Các couplingof dùng một lần màn hình-printedelectrodes (SPEs)với tước kỹ thuật trình bày một thay thế hấp dẫn chophân tích bóc thông thường. SPE liên quan đến một khối lượng pro-duction công nghệ dựa trên các kiểm tra của electroconductivevà chống thấm mực vào chất nền phẳng (nhựa, gốm,vv.) tại một độ dày kiểm soát. Việc sử dụng của tước analy-sis dựa SPEs loại bỏ các vấn đề liên quan đến việc sử dụngthông thường các tế bào electrochemical: xử lý kiêm bersome liên kết, các thủ tục dài làm sạch và cácnhu cầu về một bước de-thoáng, bằng cách sử dụng kỹ thuật điệnít bị ảnh hưởng bởi sự can thiệp của oxy. Hơn nữa, SPEs liên quandụng cụ có thể được di động bằng cách bao gồm một pin nhỏ gọnđạt được một thiết bị thể triển khai lĩnh vực người dùng thân thiện cho phépthedirectmonitoring of heavymetal traces inanin situcontrolof pollution[20–23].ASV coupled to SPEs using a variety of electrode designsand experimental protocols were used for the detection ofPb and Cd contained in different matrices such as naturalwaters[21–27], soil extracts [21,22,27], wastewater [21,26]anddrinking waters[23,25]. On the other hand, Zen et al. devel-oped a Cu/Hg-plated screen-printed electrode for single Pbdetermination contained in various waters samples, includ-ing seawater, by square wave anodic stripping voltammetry[28]. To the best of our knowledge, simultaneous determina-tion of Cd and Pb in seawater has not been reported up todate.The present study focuses on the evaluation of the feasi-bility of using SPEs for the simultaneous determination of Pband Cd in seawater. Several parameters affecting the system,such as the matrix effect upon the SPE response and the sta-bility of the measuring system have been studied. The resultsobtained for the determination of the metal contents in realand spiked seawater samples will be shown.2. Experimental2.1. Chemicals and apparatusHeavy metals solutions were prepared by diluting AAS grade(Panreac) Pb, Cd, Cu and Zn standard solutions. HCl (32%) wasobtained from Fluka. NaCl (99.5%) was purchased from Pan-reac. The pH was adjusted by using CaCO3(99%) (Merck).A certified reference material (LGC6016) consisting ofestuarine water was used for validation purposes. Thecertified metal values: 101±2g/kgCd, 190±4g/kgCu,196±3g/kgPb, and 976±31g/kgMn.The SPE sensors (from University of Florence—availablefrom PalmInstruments,http://www.palmsens.com) consistedof a screen-printed electrochemical cell with three electrodesin one single strip: a graphite working electrode modified witha plasticizer mixed with mercury acetate, a graphite counterelectrode and a silver pseudo-reference electrode[21].A computer-controlled Autolab PGSTAT-12 (302N-High per-formance) (potentiostat/galvanostat) with general-purposeselectrochemical software operating system (GPES version4.9.007) from Eco Chemie B.V., The Netherlands, was used
đang được dịch, vui lòng đợi..