1.1 PHẦN BAO GỒM: A. cung cấp và cài đặt: 1. Hội đồng quản trị của thạch cao. 2. bê thạch cao fabrications [GFRG, thạch cao gia cố kính sợi]. 3. âm thanh cách điện. 4. truy cập vào cửa và bảng trong hội đồng hội đồng quản trị thạch cao. Sinh liên quan đến phần: Không giới hạn, bao gồm phần có liên quan: Chất bịt kín chung âm thanh phần 07 9220 Phần 09 2215 nội thất phòng không cấu trúc kim loại khung Phần 09 2813 sợi thạch cao Ban Phần 09 3000 ốp lát Phần 09 9000 sơn và1.2 CỐ: A. dữ liệu sản phẩm: Của nhà sản xuất dữ liệu bao gồm hướng dẫn, khuyến nghị, và hạn chế. 1.3 đảm bảo chất lượng: Thực hiện theo phần 01 4337 tại nơi mẫu.Phần 2 - sản phẩm2.1 THẠCH CAO HỘI ĐỒNG QUẢN TRỊ: A. tiêu chuẩn: ASTM C1396 đặc tả tiêu chuẩn cho thạch cao ban, TCVN 8256:2009: thạch cao ban - đặc điểm kỹ thuật, TCVN 8257:2009: thạch cao ban - thử nghiệm phương pháp, QCVN16:2014-quốc gia kỹ thuật quy định về sản phẩm, hàng hoá vật liệu xây dựng. Sinh kính Mat thạch cao ban: ASTM C1178 đặc tả tiêu chuẩn cho kính tráng Mat nước- C. thạch cao bảng cơ sở của thiết kế: "Sheetrock cùng với SupraCeil kim loại khung cách 0.5 mm dày, 605 mm khoảng cách", chính phủ Hoa Kỳ Boral thạch cao Việt Nam, www.usgboral.com. Mất phần hợp chất và băng: đặc tả tiêu chuẩn ASTM C475 cho hợp chất chung và khớp băng cho thạch cao khi kết thúc hội đồng quản trị. E. trim: Giấy phải đối mặt kim loại "băng trên" góc hạt, cạnh hạt và xe. F. dây khóa phec mơ: ASTM C954 hoặc ASTM C1002. G. âm thanh cách điện cơ sở của thiết kế: "Thermafiber SAFB, âm thanh sự suy giảm cháy chăn", Thermafiber, Inc, www.thermafiber.com2.2 PRECAST THẠCH CAO, SỢI THỦY TINH GIA CỐ THẠCH CAO [GFRG]: A. các nhà sản xuất: 1. Formglas sản phẩm, Ltd., http://www.formglas.com 2. Pittcon ngành công nghiệp, http://www.pittconindustries.com 3. Stromberg kiến trúc, http://www.strombergarchitectural.com Sinh tiêu chuẩn: 1. tiêu chuẩn ASTM C1355 đặc tả tiêu chuẩn cho sợi thủy tinh gia cố vật liệu tổng hợp thạch cao 2. tiêu chuẩn ASTM C1381Standard đặc điểm kỹ thuật cho sợi đúc thủy tinh gia cố phần thạch cao C. kích thước, hình dạng, Hồ sơ: Tùy chỉnh như được hiển thị. 1. hoàn tất: Mịn cho lĩnh vực áp dụng sơn. 2. seams: Che dấu, lĩnh vực ghi âm sẵn và hoàn thành. 3. nhà máy tăng cường và chặn: yêu cầu tại seams.2.3 TRUY CẬP VÀO CỬA VÀ BẢNG: A. các nhà sản xuất: 1. Acudor sản phẩm, Inc, www.acudor.com 2. JL ngành công nghiệp, các bộ phận của tập đoàn Activar xây dựng sản phẩm, www.jlindustries.com 3. sản phẩm xây dựng Nystrom, www.nystrom.com 4. Williams Brothers Corporation of America, www.wbdoors.com B. truy cập vào cửa và lịch trình bảng điều khiển - cơ sở của thiết kế sản phẩm: 1. bảng thạch cao, không cháy xếp: "DW-5015", Acudor sản phẩm, Inc, www.acudor.com 2. Ban thạch cao, xếp hạng cháy: "FB-5060", Acudor sản phẩm, Inc, www.acudor.com 3. nhà vệ sinh phòng, không cháy đánh giá cao: "thép không gỉ UF-5000", Acudor sản phẩm, Inc C. vòng đệm: Yêu cầu cho hỏa lực phòng không xếp hạng cửa/bảng bao quanh plenums. D. Sizes: As shown or, if not shown: 1. Hand and Arm Reach In Only: ≥200 x 200 mm. 2. Upper Body Reach In: ≥ 600 x 600 mm. 3. Body Pass Through: ≥900 x 900 mm. E. Latches, Not Fire Rated: Screw driver cam latch. F. Latches, Fire Rated: Manufacturer’s standard for fire rated product, removable key or knob. G. Locks: Required for all public accessible doors and panels. 1. Master key into Campus keying system.Part 3 - Execution3.1 GYPSUM BOARD INSTALLATION: Comply with manufacturer's instructions and recommendations. A. Standards: Comply with: ASTM C840 Standard Specification for Application and Finishing of Gypsum Board. Gypsum Association GA-216 Application and Finishing of Gypsum Panel Products Gypsum Association GA-220 Gypsum Board Winter Related Installation Recommendations Gypsum Association GA-225 Repair of Fire-Rated Gypsum Board Systems Gypsum Association GA-226 Application of Gypsum Board To Form Curved Surfaces Gypsum Association GA-231Assessing Water Damage To Gypsum Board Gypsum Association GA-234 Control Joints for Fire-Resistance Rated Systems Gypsum Association GA-238 Guidelines for Prevention of Mold Growth on Gypsum Board Gypsum Association GA-618 Building and Inspecting Smoke Barriers B. Gypsum Board Installation: 1. Install ceilings prior to walls. 2. Locate joints as far from center of walls and ceilings as possible. 3. Install board face side out. 4. Install board joints and edges over framing members. 5. Stagger vertical joints on opposite sides of walls and in multiple layer work. 6. Do not butt dissimilar board edges. 7. Do not locate a tapered board edge at a framed opening or at wall base. 8. Provide one piece boards around penetrations, except where control joints are provided. 9. Continuously cover and protect framing, vapor retarders, and interior insulation. 10. Maintain continuity of fire rated assemblies at recessed items and penetrations. 11. Provide additional gypsum board layers behind and around items recessed into partitions. 12. Maintain acoustical performance of assemblies at recessed items and penetrations. C. Beads, Trim, and Reinforcing Tape: 1. Install beads and trims plumb, level, and accurately aligned. 2. Provide continuous beads and trims. Minimize seams. 3. Provide accurately fitted, hair line tight seams in running work. 4. Provide accurately fitted, hair line tight mitered joints at intersections. 5. Fill seams with paintable acrylic sealant. 6. Provide continuous corner bead at outside, convex corners and changes of plane. 7. Provide continuous reinforcing tape at inside, concave corners and changes of plane. 8. Provide additional reinforcing tape at corners of penetrations to help reduce stress cracks. 9. Provide continuous trim for all visible board edges, reveals, and sealant joints.3.2 GYPSUM BOARD CONTROL JOINTS: A. Control Joint Locations: Obtain Architect’s approval of each control joint location prior to installation. B. Control Joints - Not Fire Rated: Provide framing on both sides of control joints. Interrupt gypsum board at control joints. C. Control Joints - Fire Rated: Comply with Gypsum Association GA-234 Control Joints for Fire-Resistance Rated Systems.3.3 GYPSUM BOARD FIRE RATED ASSEMBLIES: Match UL design numbers.3.4 ACOUSTICAL INSULATION: Provide continuous acoustical insulation within gypsum board partitions.3.5 ACOUSTICAL SEALING: Comply with Section 07 9220 Acoustical Joint Sealants.3.6 PRECAST PLASTER, GLASS FIBER REINFORCED GYPSUM [GFRG] INSTALLATION: A. Standard: ASTM C1467 Standard Specification for the Installation of Molded Glass Fiber Reinforced Gypsum Parts. B. Coordinate light gage steel framing, building systems, and all related work. C. Install plumb and level. D. Provide invisible seams after field painting.3.7 GYPSUM BOARD FINISHING: Comply with GA-214 “Recommended Levels of Gypsum Board Finish”.End of Section
đang được dịch, vui lòng đợi..
![](//viimg.ilovetranslation.com/pic/loading_3.gif?v=b9814dd30c1d7c59_8619)