4.13 Production4.13.1 PurposeThis m

4.13 Production
4.13.1 Purpose
This mask shows production and service-relevant data.
4.13.2 Description of the mask
In the area of Production the shot counter can be activated and
reset. Also the photo sensor can be set here.
"Production settings (Production)“ Mask
4.13.3 Description of the elements
Production
Designation Description
Use Prod.counter Activation of the Prod.counter. Once the targeted shots have
been attained, production is halted.
Reset shotcounter Resetting the shot counter to 0.
Use photosensor Activation of the photosensor for mold monitoring.
Photosensor timeout If the monitoring time is exceeded, an error is triggered.
Sensor monitor time Specification of the maximum duration of the procedure of the
sensor. If this time is exceeded an alarm will be triggered.
cavity It can produce the amount of the production on one mold.
Prof.Stage
With specific movements, it is possible to specify (profile points)
pressure and amount for different path sections. How many profile
points are available for the respective movement is adjusted here.
Designation Description
Inject Number of profile points for injecting.
Hold Number of profile points for hold pressure.
Plasticize Number of profile points for plasticizing.
Mold open Number of profile points for mold open
Mold close Number of profile points for mold close.
Ejector forward Number of profile points for ejector forward.
Ejector backward Number of profile points for ejector backward.
4.14 Monitoring time (Max.Times)
4.14.1 Purpose
The monitoring time mask serves to set monitoring times.
4.14.2 Description of the mask
Here the maximum times are set for the entire machine cycle as well
as single processes.
In addition to the runtime also the current times of the cycle as well
as their difference to the maximum times is shown.
Note
These maximum times apply only for semi-automatic and automatic
mode.
"Monitoring time" mask
4.14.3 Description of the elements
Monitoring time (Max.Times)
Once the monitoring time has been exceeded, an alarm is triggered.
Designation Description
Machine cycle The duration of the current machine cycle is shown in the left field
(grey). The monitoring time is entered in the middle field Limit.
The difference between the two values is shown in the right field
Differ.
Mold open The duration of Mold open is shown in the left field Actual (grey).
The monitoring time is entered in the middle field Limit. The
difference between the two values is shown in the right field
Differ.
Mold close The duration of Mold close is shown in the left field Actual (grey).
The monitoring time is entered in the middle field Limit. The
difference between the two values is shown in the right field
Differ.
Ejector forward The duration for Ejector forward is shown in the left field Actual
(grey). The monitoring time is entered in the middle field Limit.
The difference between the two values is shown in the right field
Differ.
Ejector backward The duration for Ejector backward is shown in the left field Actual
(grey). The monitoring time is entered in the middle field Limit.
The difference between the two values is shown in the right field
Differ.
Inject The duration for Inject is shown in the left field Actual (grey). The
monitoring time is entered in the middle field Limit. The difference
between the two values is shown in the right field Differ.
Plasticise The duration for plasticise is shown in the left field Actual (grey).
The monitoring time is entered in the middle field Limit. The
difference between the two values is shown in the right field
Differ.
Designation Description
Auto Purge The duration for Purge is shown in the left field Actual (grey). The
monitoring time is entered in the middle field Limit. The difference
between the two values is shown in the right field Differ.
Mold Adjust The duration for mold adjust is shown in the left field Actual
(grey). The monitoring time is entered in the middle field Limit.
The difference between the two values is shown in the right field
(Differ.).
SkBk The duration for screw moving backword is shown in the left field
Actual (grey). The monitoring time is entered in the middle field
Limit. The difference between the two values is shown in the right
field Differ.
4.15 Delay Times
4.15.1 Purpose
This mask is used for adjusting the delay times in production mode.
4.15.2 Description of the mask
Delay times for difference processes in the production and manual
operation can be defined here in order to prevent jerky movements.
These processes start only after the specified delay times that have
been set for them have expired.
For every movement, delay times for start movement (Movement),
activate pump (Pump) and deactivate control valve (Valve) can be
adjusted.