Head Office Of Viet Nam Jointstock

Head Office Of Viet Nam Jointstock Commercial Bank Vinaconex R&D Jointstock Company
For Industry And Trade CONSTRUCTION DOCUMENTS – 2013.09.05
VietinBank Tower PAINTING
Hanoi, Vietnam 099000 - 1
SECTION 099000
PAINTING
PART 1 GENERAL
1.1 SUMMARY
A. The work of this Section shall include, but not necessarily be limited to:
1. Field painting of exposed interior items and surfaces.
2. Field painting of exposed exterior items and surfaces.
3. Surface preparation for painting.
B. Coordination: Coordinate the work with that of other Trade Contractors to ensure proper
execution of the work of both trades. Examine Contract Documents for requirements that
directly affect or are affected by Work of this Section.
1. Drawings and general provisions of the Contract, including Division 00 Documents and
Division 01 Specification Sections, apply to this Section. Other related sections include,
but are not limited to:
a. Section 051200 - STRUCTURAL STEEL FRAMING.
b. Section 055000 - METAL FABRICATIONS.
c. Section 064023 - INTERIOR ARCHITECTURAL WOODWORK.
d. Section 081113 - HOLLOW METAL DOORS AND FRAMES.
e. Section 081416 - FLUSH WOOD DOORS.
f. Section 092116 - GYPSUM BOARD ASSEMBLIES.
g. Section 092300 - GYPSUM PLASTERING.
h. Section 092400 - PORTLAND CEMENT PLASTER.
i. Section 092713 - GLASS-FIBER-REINFORCED PLASTER FABRICATIONS.
C. Extra Materials:
1. Maintenance Materials: Provide 2 sealed cans of 5 L capacity minimum of each
product, in each color used in the work, for Employer’s use in maintenance. Containers
to be new, fully labeled with manufacturer’s name, type of paint, and color.
1.2 QUALITY CONTROL REQUIREMENTS
A. Pre Contract Samples:
1. Technical literature.
B. Post Contract Samples:
1. 1000mm x 1000mm sample of finish.
C. Mock-Ups:
1. As required by the Engineer and/or the PM/CM.
D. Prototypes:
1. As required by the Engineer and/or the PM/CM.
E. Benchmarks:
1. The first fully completed bay on specified substrate or full unit item on site.
1.3 SUSTAINABILITY REQUIREMENTS
A. Employer has established and Contractor must follow environmental objectives and
Head Office Of Viet Nam Jointstock Commercial Bank Vinaconex R&D Jointstock Company
For Industry And Trade CONSTRUCTION DOCUMENTS – 2013.09.05
VietinBank Tower PAINTING
Hanoi, Vietnam 099000 - 2
implementation strategies created for this Project based on the USGBC LEED Green
Building Rating System and the VGBC LOTUS Green Building System. Although the Office
Tower is the only part of the Project that is seeking LEED and LOTUS certification, the
Employer requires that the construction of the entire Project be performed with careful
adherence to the sustainability goals laid out in the following documents:
1. Section 017419 - CONSTRUCTION WASTE MANAGEMENT AND DISPOSAL.
2. Section 018113 - SUSTAINABLE DESIGN REQUIREMENTS.
3. Section 018117 - SUSTAINABILITY ACTION PLAN.
4. Section 018119 - CONSTRUCTION INDOOR AIR QUALITY MANAGEMENT.
B. Building Rating: The Office Tower is seeking rating under both the USGBC LEED Green
Building System and the VGBC LOTUS Non-Residential Rating Tool, as follows:
1. USGBC LEED Rating: Comply with project requirements intended to achieve the
following Rating, as measured and documented according to the USGBC LEED Green
Building Rating System, Version indicated:
a. Rating: Gold.
b. Version: LEED 2009 for Core & Shell.
2. VGBC LOTUS Rating: Comply with project requirements intended to achieve the
following Rating, as measured and documented according to the VGBC LOTUS Rating
System, Version indicated:
a. Rating: Silver.
b. Version: LOTUS Non-Residential Pilot.
3. Division 01 Requirements specific to the ratings, in addition to those indicated in
Paragraph 1.3A. herein, include:
a. Section 018115 - LEED REQUIREMENTS SUMMARY.
b. Section 018116 - LOTUS REQUIREMENTS SUMMARY.
c. Section 019113 - GENERAL COMMISSIONING REQUIREMENTS.
C. Materials Sustainability Requirements:
1. Use field applied paints and coatings that comply with the VOC limits and chemical
restrictions specified in the Sustainability Action Plan.
1.4 SYSTEM DESCRIPTION
A. Material Codes:
1. Type PT-101 Emulsion Paint Finish:
a. Emulsion paint to substrates as indicated on the Drawings.
b. Preparation shall be carried out in accordance with the manufacturer's
instructions.
c. The required number of coatings and application shall be carried out in
accordance with the manufacturers instructions.
d. The color shall be accepted by the Engineer through the submittal of samples.
2. Type PT-102 Epoxy Floor Paint:
a. Epoxy floor paint to floor areas as indicated on the Drawings.
b. Provide a two part component water dispersal epoxy resin coating system to meet
the performance requirements.
c. Preparation shall be carried out in accordance with the manufacturer's
instructions.
d. The color shall be accepted by the Engineer through the submittal of samples.
e. Mixing and application shall be carried out in accordance with the manufacturer's
written instructions.
3. Type PT-103 Epoxy Floor Paint:
a. Epoxy floor paint to floor areas as indicated on the Drawings.
b. Provide a two part component water dispersal epoxy resin coating system to meet
the performance requirements.
c. Preparation shall be carried out in accordance with the manufacturer's
instructions.
Head Office Of Viet Nam Jointstock Commercial Bank Vinaconex R&D Jointstock Company
For Industry And Trade CONSTRUCTION DOCUMENTS – 2013.09.05
VietinBank Tower PAINTING
Hanoi, Vietnam 099000 - 3
d. The color shall be accepted by the Engineer through the submittal of samples.
e. Mixing and application shall be carried out in accordance with the manufacturer's
written instructions.
4. Type PT-201 Concrete Paint - External:
a. Concrete/ masonry paint to substrates as indicated on the Drawings.
b. Preparation shall be carried out in accordance with the manufacturer's
instructions.
c. The required number of coatings and application shall be carried out in
accordance with the manufacturers instructions.
d. There shall be a minimum 2 full finishing coats of concrete/ masonry paint.
e. The color shall be accepted by the Engineer through the submittal of samples.
B. Requirements, General:
1. All materials, labour and equipment required to complete the painting work, together
with ancillary work described and implied, to the full intent of the drawings and
schedules.
2. Make thorough examination of drawings, details and schedules, determine the intent,
extent, materials, types of surfaces, locations, and be fully cognizant of requirements.
3. Examine the specifications and drawings for the work of other Sections regarding the
provisions for prime and finish coats. Paint or finish all materials installed throughout
the project, which are required to be painted or finished and which are left unfinished or
unpainted by other Sections.
4. For areas indicated as unfinished in the Room Finish Schedule, painting is As required
by the Engineer and/or the PM/CM except for the following: all structural steel, doors
and frames, railings, miscellaneous metal work, insulation on mechanical pipes and
equipment, pipes and fittings, electrical mounting boards and all gypsum board
surfaces. See schedule for colors.
5. Painting includes field painting of exposed bare and covered pipes and ducts (including
color coding), hangers, exposed steel and iron supports, and surfaces of mechanical
and electrical equipment that do not have a factory-applied final finish.
6. Whether specified or not in the Room Finish Schedule, all gypsum board surfaces
shall, as a minimum, be prime painted.
7. Paint all exposed exterior unfinished, primed or galvanized steel.
8. Do not paint prefinished items, concealed surfaces, finished metal surfaces, operating
parts, and labels.
a. Prefinished items include the following factory-finished components:
1). Architectural woodwork.
2). Acoustical wall panels.
3). Metal toilet enclosures.
4). Metal lockers.
5). Kitchen appliances.
6). Elevator entrance doors and frames.
7). Elevator equipment.
8). Finished mechanical and electrical equipment.
9). Light fixtures.
b. Concealed surfaces include walls or ceilings in the following generally
inaccessible spaces:
1). Foundation spaces.
2). Furred areas.
3). Ceiling plenums.
4). Utility tunnels.
5). Pipe spaces.
6). Duct shafts.
7). Elevator shafts.
c. Finished metal surfaces include the following:
1). Anodized aluminum.
2). Stainless steel.
3). Chromium plate.
4). Copper and copper alloys.
Head Office Of Viet Nam Jointstock Commercial Bank Vinaconex R&D Jointstock Company
For Industry And Trade CONSTRUCTION DOCUMENTS – 2013.09.05
VietinBank Tower PAINTING
Hanoi, Vietnam 099000 - 4
5). Bronze and brass.
d. Operating parts include moving parts of operating equipment and the following:
1). Valve and damper operators.
2). Linkages.
3). Sensing devices.
4). Motor and fan shafts.
e. Labels: Do not paint over code-required labels or equipment name, identification,
performance rating, or nomenclature plates.
C. Definitions:
1. Sheen Levels: Sheen levels shall be defined in accordance with the following values.
Final sheens to be taken from the Samples or Quality Benchmark Installations:
a. Flat Sheen: 10% (±5%) gloss, viewed at 850mm from source.
b. Low Sheen: 15% (±5%) gloss, viewed at 600mm from source.
c. Mid Sheen: 25% (±5%) gloss, viewed at 600mm from source.
d. High Sheen: 85% (±5%) gloss, viewed at 200mm from source.

Kết quả (Việt) 1:

Trụ sở chính của ngân hàng thương mại cổ Việt Nam Vinaconex R & công ty cổ phần D Về công nghiệp và thương mại tài liệu xây dựng-2013.09.05 Bức tranh VietinBank Tower Hà Nội, Việt Nam 099000-1 PHẦN 099000 BỨC TRANH PHẦN 1 TỔNG 1.1 TÓM TẮT A. công việc của phần này sẽ bao gồm, nhưng không nhất thiết phải được giới hạn ở: 1. lĩnh vực bức tranh của tiếp xúc với trang trí nội thất và các bề mặt. 2. lĩnh vực bức tranh tiếp xúc bên ngoài mục và bề mặt. 3. bề mặt để chuẩn bị cho bức tranh. Sinh phối hợp: Phối hợp làm việc với các nhà thầu thương mại để đảm bảo phù hợp thực hiện các công việc của cả hai ngành nghề. Kiểm tra hợp đồng cho các yêu cầu mà trực tiếp ảnh hưởng đến hoặc là ảnh hưởng bởi các tác phẩm của phần này. 1. bản vẽ và các quy định chung của hợp đồng, bao gồm cả bộ phận 00 tài liệu và Bộ phận 01 đặc điểm kỹ thuật phần, áp dụng cho phần này. Bao gồm các phần có liên quan khác, nhưng là không giới hạn đối với: a. phần 051200 - kết cấu thép khung. sinh phần 055000 - kim loại FABRICATIONS. c. phần 064023 - đồ gỗ nội thất kiến trúc. mất phần 081113 - rỗng kim loại cửa ra vào và khung. e. phần 081416 - tuôn ra gỗ cửa. f. phần 092116 - hội đồng hội đồng quản trị thạch cao. g. phần 092300 - thạch cao PLASTERING. h. phần 092400 - xi măng PORTLAND thạch cao. i. phần 092713 - thủy tinh-sợi tăng cường thạch cao FABRICATIONS. C. phụ vật liệu: 1. bảo trì tài liệu: Cung cấp 2 lon 5 L công suất tối thiểu của mỗi kín sản phẩm, trong mỗi màu sắc được sử dụng trong công việc, để sử dụng của nhà tuyển dụng trong bảo trì. Thùng chứa để được mới, đầy đủ có nhãn với tên của nhà sản xuất, loại sơn, và màu sắc. 1.2 CHẤT LƯỢNG ĐIỀU KHIỂN YÊU CẦU A. mẫu hợp đồng trước: 1. kỹ thuật văn học. B. bài mẫu hợp đồng: 1. 1000 mm x 1000 mm mẫu kết thúc. C. giả-up: 1. là yêu cầu của các kỹ sư và/hoặc am/CM. Mất nguyên mẫu: 1. là yêu cầu của các kỹ sư và/hoặc am/CM. E. điểm chuẩn: 1. Vịnh hoàn toàn hoàn thành đầu tiên trên bề mặt đã chỉ định hoặc đơn vị đầy đủ mục trên trang web. 1.3 PHÁT TRIỂN BỀN VỮNG YÊU CẦU A. sử dụng lao động đã thành lập và nhà thầu phải tuân theo các mục tiêu về môi trường và Trụ sở chính của ngân hàng thương mại cổ Việt Nam Vinaconex R & công ty cổ phần D Về công nghiệp và thương mại tài liệu xây dựng-2013.09.05 Bức tranh VietinBank Tower Hà Nội, Việt Nam 099000-2 thực hiện chiến lược tạo ra cho dự án này dựa trên USGBC LEED Green Tòa nhà đánh giá hệ thống và hệ thống công trình xanh hoa sen làm. Mặc dù các văn phòng Tháp là phần duy nhất của dự án là tìm kiếm chứng nhận LEED và LOTUS, các Sử dụng lao động yêu cầu xây dựng toàn bộ dự án được thực hiện với cẩn thận tuân thủ các mục tiêu phát triển bền vững đặt ra trong các tài liệu sau đây: 1. phần 017419 - quản lý chất thải xây dựng và xử lý. 2. phần 018113 - yêu cầu thiết kế bền vững. 3. phần 018117 - kế hoạch hành động phát triển bền vững. 4. Section 018119 - CONSTRUCTION INDOOR AIR QUALITY MANAGEMENT. B. Building Rating: The Office Tower is seeking rating under both the USGBC LEED Green Building System and the VGBC LOTUS Non-Residential Rating Tool, as follows: 1. USGBC LEED Rating: Comply with project requirements intended to achieve the following Rating, as measured and documented according to the USGBC LEED Green Building Rating System, Version indicated: a. Rating: Gold. b. Version: LEED 2009 for Core & Shell. 2. VGBC LOTUS Rating: Comply with project requirements intended to achieve the following Rating, as measured and documented according to the VGBC LOTUS Rating System, Version indicated: a. Rating: Silver. b. Version: LOTUS Non-Residential Pilot. 3. Division 01 Requirements specific to the ratings, in addition to those indicated in Paragraph 1.3A. herein, include: a. Section 018115 - LEED REQUIREMENTS SUMMARY. b. Section 018116 - LOTUS REQUIREMENTS SUMMARY. c. Section 019113 - GENERAL COMMISSIONING REQUIREMENTS. C. Materials Sustainability Requirements: 1. Use field applied paints and coatings that comply with the VOC limits and chemical restrictions specified in the Sustainability Action Plan. 1.4 SYSTEM DESCRIPTION A. Material Codes: 1. Type PT-101 Emulsion Paint Finish: a. Emulsion paint to substrates as indicated on the Drawings. b. Preparation shall be carried out in accordance with the manufacturer's instructions. c. The required number of coatings and application shall be carried out in accordance with the manufacturers instructions. d. The color shall be accepted by the Engineer through the submittal of samples. 2. Type PT-102 Epoxy Floor Paint: a. Epoxy floor paint to floor areas as indicated on the Drawings. b. Provide a two part component water dispersal epoxy resin coating system to meet the performance requirements. c. Preparation shall be carried out in accordance with the manufacturer's instructions. d. The color shall be accepted by the Engineer through the submittal of samples. e. Mixing and application shall be carried out in accordance with the manufacturer's written instructions. 3. Type PT-103 Epoxy Floor Paint: a. Epoxy floor paint to floor areas as indicated on the Drawings. b. Provide a two part component water dispersal epoxy resin coating system to meet the performance requirements. c. Preparation shall be carried out in accordance with the manufacturer's instructions. Head Office Of Viet Nam Jointstock Commercial Bank Vinaconex R&D Jointstock Company For Industry And Trade CONSTRUCTION DOCUMENTS – 2013.09.05 VietinBank Tower PAINTING Hanoi, Vietnam 099000 - 3 d. The color shall be accepted by the Engineer through the submittal of samples. e. Mixing and application shall be carried out in accordance with the manufacturer's written instructions. 4. Type PT-201 Concrete Paint - External: a. Concrete/ masonry paint to substrates as indicated on the Drawings. b. Preparation shall be carried out in accordance with the manufacturer's instructions. c. The required number of coatings and application shall be carried out in accordance with the manufacturers instructions. d. There shall be a minimum 2 full finishing coats of concrete/ masonry paint. e. The color shall be accepted by the Engineer through the submittal of samples. B. Requirements, General: 1. All materials, labour and equipment required to complete the painting work, together with ancillary work described and implied, to the full intent of the drawings and schedules. 2. Make thorough examination of drawings, details and schedules, determine the intent, extent, materials, types of surfaces, locations, and be fully cognizant of requirements. 3. Examine the specifications and drawings for the work of other Sections regarding the provisions for prime and finish coats. Paint or finish all materials installed throughout the project, which are required to be painted or finished and which are left unfinished or unpainted by other Sections. 4. For areas indicated as unfinished in the Room Finish Schedule, painting is As required by the Engineer and/or the PM/CM except for the following: all structural steel, doors and frames, railings, miscellaneous metal work, insulation on mechanical pipes and equipment, pipes and fittings, electrical mounting boards and all gypsum board surfaces. See schedule for colors. 5. Painting includes field painting of exposed bare and covered pipes and ducts (including color coding), hangers, exposed steel and iron supports, and surfaces of mechanical and electrical equipment that do not have a factory-applied final finish. 6. Whether specified or not in the Room Finish Schedule, all gypsum board surfaces shall, as a minimum, be prime painted. 7. Paint all exposed exterior unfinished, primed or galvanized steel. 8. Do not paint prefinished items, concealed surfaces, finished metal surfaces, operating parts, and labels. a. Prefinished items include the following factory-finished components: 1). Architectural woodwork. 2). Acoustical wall panels. 3). Metal toilet enclosures. 4). Metal lockers. 5). Kitchen appliances. 6). Elevator entrance doors and frames. 7). Elevator equipment. 8). Finished mechanical and electrical equipment. 9). Light fixtures. b. Concealed surfaces include walls or ceilings in the following generally inaccessible spaces: 1). Foundation spaces. 2). Furred areas. 3). Ceiling plenums. 4). Utility tunnels. 5). Pipe spaces. 6). Duct shafts. 7). Elevator shafts. c. Finished metal surfaces include the following: 1). Anodized aluminum. 2). Stainless steel. 3). Chromium plate. 4). Copper and copper alloys. Head Office Of Viet Nam Jointstock Commercial Bank Vinaconex R&D Jointstock Company For Industry And Trade CONSTRUCTION DOCUMENTS – 2013.09.05 VietinBank Tower PAINTING
Hanoi, Vietnam 099000 - 4
5). Bronze and brass.
d. Operating parts include moving parts of operating equipment and the following:
1). Valve and damper operators.
2). Linkages.
3). Sensing devices.
4). Motor and fan shafts.
e. Labels: Do not paint over code-required labels or equipment name, identification,
performance rating, or nomenclature plates.
C. Definitions:
1. Sheen Levels: Sheen levels shall be defined in accordance with the following values.
Final sheens to be taken from the Samples or Quality Benchmark Installations:
a. Flat Sheen: 10% (±5%) gloss, viewed at 850mm from source.
b. Low Sheen: 15% (±5%) gloss, viewed at 600mm from source.
c. Mid Sheen: 25% (±5%) gloss, viewed at 600mm from source.
d. High Sheen: 85% (±5%) gloss, viewed at 200mm from source.