Các loại khác nhau của piston và trục vít máy nén bắt đầu trong differents cách. Một số loại
có prelubrication trong khi những người khác bắt đầu directly.Under mọi trường hợp báo động nhất định đang bị đàn áp ở giai đoạn này như mô tả trong phần Báo động và cảnh báo và Thời Gian.
SAB 202, SAB 163H / 128H MK3 với bơm dầu VMY Mk3 với bơm lưu lượng đầy đủ.
Các máy bơm được sử dụng cho prelubrication và duy trì một mức áp suất dầu tối thiểu trong khi hoạt động. Bơm này được bắt đầu và dừng lại phù hợp với các áp lực khác biệt giữa máy nén trong khi hoạt động.
Sự khác biệt được thiết lập trong hình DẦU tôi DẦU ÁP Tôi tham số và rồi SET
POINT 1 và SET POINT 2 xuất hiện.
SET POINT 1 là áp suất mà tại đó các máy bơm để bắt đầu, và SET POINT 2 là áp suất tại
đó là bơm đang dừng lại. Do đó, điều chỉnh SET POINT 1 đến mức áp suất thấp nhất.
Thiết lập bình thường cho SAB 202:
SET POINT 1 = 2,5 Bar
SET POINT 2 = 4 Bar
Di chuyển con trỏ đến SET POINT 1 và nhấn G cho đến khi con trỏ di chuyển sang bên phải trong hình .
với K và J thiết lập giá trị. . Khi giá trị đã được thiết lập, bấm G một lần nữa
Trong cùng một cách điều chỉnh SET POINT 2.
Nếu chênh áp nén (áp lực xả - áp lực hút). Dưới SET POINT 1 trong khi hoạt động, máy bơm sẽ bắt đầu ngay lập tức
khi máy nén chênh áp đã cao hơn so với SET POINT 2 trong 60 giây, các
máy bơm sẽ dừng lại.
khởi động chuỗi
Khi máy nén đã nhận được bắt đầu cho phép, bơm dầu đầy đủ lưu lượng sẽ bắt đầu. Hãy chắc chắn rằng các slide khả năng là ở vị trí tối thiểu. Mở SAB 202 này nói chung là luôn luôn như vậy với thanh trượt được đẩy xuống bởi một lò xo.
Dầu được bơm vào hệ thống bôi trơn máy nén, và khi chuyển đổi lưu lượng dầu được kích hoạt, thời gian prelubrication sẽ bắt đầu.
Khi thời gian đã hết hạn các máy nén được bắt đầu và bơm bây giờ sẽ chạy cho min 60 sec.
các máy bơm sẽ dừng lại khi các áp lực khác biệt là ở trên SET POINT 2 như đã mô tả ở trên.
giám sát báo động
trong bắt đầu báo động sau đây được trì hoãn:
đang được dịch, vui lòng đợi..