1. ASSIENMENT [2] METAL HÌNH THÀNH TỔNG QUESTIONS1- sự khác biệt giữa các quá trình biến dạng lớn và quá trình kim loại tấm là gì? Trả lời. Trong biến dạng rời, thay đổi hình dạng là đáng kể, và các bộ phận công trình có tỷ lệ diện tích alow-to-khối lượng. Trong quá trình kim loại tấm, tỷ lệ diện tích-to-khối lượng là đùn high.2- là một quá trình định hình cơ bản. Miêu tả nó. Bài giải. Đùn là một quá trình nén trong đó vật liệu công việc buộc phải chảy qua một lỗ chết, do đó buộc cắt ngang của nó để giả hồ sơ cá nhân của orifice.3- Tại sao báo chí hạn bộ làm việc thường được sử dụng cho quá trình kim loại tấm? Bài giải. Các hoạt động báo chí hạn được sử dụng bởi vì các hoạt động kim loại nhất tấm được thực hiện trên presses.4- sự khác biệt giữa bản vẽ sâu và thanh vẽ là gì? Bài giải. Sâu vẽ là một tấm kim loại hình thành quá trình sử dụng để chế tạo các bộ phận hình chén; thanh vẽ là một quá trình biến dạng với số lượng lớn được sử dụng để làm giảm đường kính của một tác phẩm hình trụ part.5- Chỉ ra phương trình toán học cho các đường cong dòng chảy. Bài giải. Các đường cong dòng chảy được xác định trong phương trình. (18.1) là YF = Kεn.6- Danh sách một số các sản phẩm được sản xuất trên một dây chuyền cán. Bài giải. Sản phẩm bao gồm cán flatsheet và chứng khoán tấm, thanh tròn và cổ phiếu thanh, đường ray, hình dạng cấu trúc như I-dầm andchannels.7- dự thảo trong một hoạt động lăn là gì? Bài giải. Dự thảo là sự khác biệt giữa độ dày bắt đầu và độ dày cuối cùng như các phôi đi qua giữa hai đối rolls.8- gì là gắn bó trong một hoạt động cán nóng? Bài giải. Gắn bó là tình trạng cán nóng trong đó bề mặt của phôi tuân thủ các cuộn như những mảnh chuyển giữa các cuộn, gây biến dạng nghiêm trọng của kim loại bên dưới bề mặt để cho phép đi qua các cuộn gap.9- Xác định một số những cách thức mà lực lượng trong cán phẳng có thể được giảm bớt. Bài giải. Cách để giảm lực trong cán phẳng bao gồm (1) sử dụng cán nóng, (2) giảm dự thảo trong từng vượt qua, và (3) sử dụng cuộn đường kính nhỏ hơn. 19,19 Phân biệt giữa đùn trực tiếp và gián tiếp. Bài giải. Trong đùn trực tiếp, còn được gọi là phía trước phun ra, một phôi kim loại được nạp vào một container, và một ram nén vật liệu, buộc phải chảy qua một lỗ chết ở cuối đối diện của hộp đựng. Trong đùn gián tiếp, còn được gọi là đùn lạc hậu, sự chết đã được đưa vào ram, và như ram nén vào phôi kim loại, kim loại được ép chảy qua lỗ chết theo một hướng mà là ngược lại (lùi) của ram motion.10- Tên một số sản phẩm được sản xuất bằng cách phun ra.
2. Bài giải. Sản phẩm được sản xuất bằng cách đùn liên tục bao gồm hình dạng cấu trúc (các khung cửa sổ, quầy hàng hoa sen, kênh), ống và ống dẫn, và que mặt cắt khác nhau. Sản phẩm làm bằng đùn rời rạc bao gồm ống kem đánh răng, lon nhôm nước giải khát, và cases.11- pin Trong tẩy trống của một phần kim loại tấm tròn, được giải phóng mặt bằng áp dụng cho các đường kính đấm orthe chết đường kính? Bài giải. Đường kính đế bằng với đường kính trống, và đường kính đục lỗ nhỏ bằng hai lần giải phóng mặt bằng. Nhiều sự lựa chọn câu hỏi 1- Điều nào sau đây là điển hình của hình học bắt đầu công việc trong quá trình kim loại tấm: (a) Tỷ lệ khối lượng cao-to-khu vực hoặc (b) tỷ lệ thấp khối lượng-to-khu vực? Bài giải. (b) .2- Các đường cong dòng chảy thể hiện hành vi của một kim loại trong đó các vùng sau của đường cong ứng suất biến dạng: (a) khu vực đàn hồi hoặc (b) khu vực nhựa? Bài giải. (b) .3- Sự căng thẳng dòng chảy trung bình là sự căng thẳng dòng chảy nhân mà trong những yếu tố sau đây: (a) n, (b) (1 + n), (c) 1 / n, hoặc (d) 1 / ( 1 + n), trong đó n là số mũ căng cứng? Bài giải. (d) .4- làm việc nóng của kim loại dùng để chỉ mà một trong những vùng nhiệt độ sau đây tương ứng với điểm nóng chảy của kim loại nhất định trên một thang đo nhiệt độ tuyệt đối: (a) nhiệt độ phòng, (b) 0.2Tm, (c) 0.4 Tm, hoặc (d) 0.6Tm? Bài giải. (d) .5- Phôi bắt đầu từ thép cán nóng thép tấm và chứng khoán là tấm đó của (một câu trả lời tốt nhất) sau đây: (a) cổ phiếu thanh, (b) phôi thép, (c) nở, (d) phiến, hoặc (e) cổ dây? Bài giải. (d) .6- Dự thảo tối đa có thể trong một hoạt động lăn phụ thuộc vào các thông số sau (hai câu trả lời đúng): (a) hệ số ma sát giữa cuộn và làm việc, (b) đường kính cuộn, (c) vận tốc roll, (d) độ dày cổ phiếu, (e) căng thẳng, và (f) Hệ số sức mạnh của kim loại công việc? Bài giải. (a) và (b) .7- Điều nào sau đây là những cái tên thay thế cho đùn gián tiếp (hai câu trả lời đúng) :( a) đùn lạc hậu, (b) đùn trực tiếp, (c) về phía trước phun ra, (d) tác động đùn, và (e) đùn ngược? trả lời. (a) và (e) .8- Việc sản xuất của ống có thể đùn gián tiếp nhưng không đùn trực tiếp: (a) đúng hoặc (b) sai?
3. Bài giải. (b). Phần ống và ống chéo có thể được sản xuất bằng cách trực tiếp hoặc indirectextrusion.9- Mà các thông số căng thẳng hoặc sức mạnh sau đây được sử dụng trong tính toán của các lực lượng trong một hoạt động đùn (một câu trả lời tốt nhất): (a) căng thẳng dòng chảy trung bình, ( b) Cường độ nén, (c) stress dòng cuối cùng, (d) độ bền kéo, (e) mang lại sức mạnh? Bài giải. (a) .10- Trong đó các hoạt động sau đây là đùn ma sát là một yếu tố trong việc xác định lực lượng theextrusion (một câu trả lời tốt nhất): (a) đùn trực tiếp hoặc (b) đùn gián tiếp? Bài giải. (a) .11- Sên tấm kim loại hình tròn được sản xuất trong một hoạt động lỗ đấm sẽ có samediameter như nào sau đây: (a) khai mạc chết hoặc (b) những cú đấm trả lời. (a) .12- Lực cắt trong một hoạt động kim loại tấm tẩy trống tùy thuộc vào mechanicalproperty của kim loại (một câu trả lời đúng): (a) cường độ nén, (b) mô đun đàn hồi, (c) sức chống cắt, (d) Tỷ lệ biến dạng, (e) độ bền kéo, hoặc (f) mang lại sức mạnh? trả lời. (c) .13- Lực lượng nắm giữ trong bản vẽ là nhiều khả năng là (a) lớn hơn, (b) bằng hoặc (c) lessthan lực lượng bản vẽ tối đa? trả lời. (c). PROBLEMS1- Hệ số sức mạnh = 550 MPa và căng thẳng-cứng mũ = 0.22 cho một certainmetal. Trong một hoạt động tạo hình, căng thẳng thật sự cuối cùng mà những kinh nghiệm kim loại = 0.85.Determine sự căng thẳng dòng chảy ở dòng này và sự căng thẳng dòng chảy trung bình mà các kim loại experiencedduring hoạt động. Giải pháp: Flow căng thẳng YF = 550 (0,85) 0,22 = 531 MPa. Căng thẳng dòng chảy trung bình fy = 550 (0,85) 0,22 / 1,22 = 435 MPa. 2- Một kim loại có một đường cong dòng chảy với các thông số: hệ số sức mạnh = 850 MPa và căng thẳng-cứng mũ = 0,30. Một mẫu vật kéo của kim loại với chiều dài gage = 100 mm isstretched đến một chiều dài = 157 mm. Xác định căng thẳng dòng chảy ở chiều dài mới và sự căng thẳng averageflow rằng các kim loại đã phải chịu trong quá trình biến dạng. Giải pháp: ε = ln (157/100) = ln 1,57 = 0,451 Dòng nhấn mạnh YF = 850 (0,451) 0,30 = 669,4 MPa. Trung bình căng thẳng dòng chảy fy = 850 (0,451) 0,30 / 1,30 = 514,9 MPa.3- Đối với một kim loại nhất định, hệ số sức mạnh = 700 MPa và căng thẳng-cứng mũ = 0,27. Xác định căng thẳng dòng chảy trung bình mà các kinh nghiệm kim loại nếu nó chịu astress đó là bằng với hệ số sức mạnh của nó K. Giải pháp:. YF = K = 700 = Kεn = 700ε.27 ε phải bằng 1,0
4. fy = 700 (1.0) 0,27 / 1,27 = 700 / 1,27 = 551,2 MPa4- Xác định giá trị của các số mũ căng-cứng cho một kim loại mà sẽ gây ra căng thẳng dòng chảy theaverage là 3/4 của sự căng thẳng dòng cuối cùng sau khi biến dạng. Giải pháp: fy = 0,75 YF Kεn / (1 + n) = 0,75 Kεn 1 / (1 + n) = 0,75 1 = 0.75 (1 + n) = 0,75 + 0,25 = 0.75n 0.75nn = 0.3335- A 2.0 trong tấm dày là 10,0 trong rộng và dài 12,0 ft. Độ dày được giảm xuống trong threesteps trong một hoạt động cán nóng. Mỗi bước sẽ làm giảm sàn 75% previousthickness của nó. Dự kiến đối với kim loại này giảm, các sàn sẽ phình thêm 3% trong eachstep. Nếu tốc độ xâm nhập của các phiến trong bước đầu tiên là 40 ft / min, và tốc độ cuộn là giống forthe ba bước, xác định: (a) chiều dài và (b) vận tốc thoát của phiến sau khi giảm thức. Giải pháp: (a) Sau khi ba đi, tf = (0,75) (0,75) (0,75) (2,0) = 0,844 trong wf = (1.03) (1.03) (1.03) (10,0) = 10,927 trong towoLo = tfwfLf (2.0) ( 10.0) (12 x 12) = (0,844) (10,927) Lf Lf = (2,0) (10,0) (12 x 12) / (0,844) (10,927) = 312,3 in = 26,025 ft (b) Cho rằng cuộn tốc độ là cùng một lúc cả ba khán đài và rằng towovo = tfwfvf, 6- Xác định lực tẩy trống cần thiết trong vấn đề 20.2, nếu thép có cường độ chịu cắt = 325MPa và độ bền kéo là 450 MPa. Giải pháp: F = STL t = 2,0 mm từ Problem 20.2. L = πD = 75π = 235,65 mm F = 325 (2.0) (235,65) = 153.200 N7- Xác định các yêu cầu trọng tải cho các hoạt động tẩy trống trong bài tập 20.4, trao thatthe thép không gỉ có độ bền cắt = 600 MPa. Giải pháp: F = STL t = 4 mm từ Problem 20.4. L = + 50 + 85 25 + 25 + 35 + 25 + 25 + 50 = 320 mm F = 600 (4.0) (320) = 768.000 N. Đây là abou
đang được dịch, vui lòng đợi..